Place of Origin:
Japan
Brand Name:
Hitachi
Certification:
CE
Model Number:
ZX210W-6
This Hitachi ZX210W-6 is a genuine 21-ton class wheeled excavator built for contractors who refuse to lose half a day on transport. Because the machine runs on its own tyres at highway speed, one unit can cover three or four separate sites in a single shift without a low-bed trailer, without an oversize permit and without tearing up fresh asphalt. Municipal repair gangs, utility contractors and road-widening crews in built-up areas get paid by the metre, and every hour saved on moving the machine is an hour billed on the bucket.
Power comes from the Isuzu 4HK1X four-cylinder turbocharged diesel with mechanical direct injection. Anyone who has maintained this generation of Hitachi understands the advantage: fuel is sprayed straight into the combustion chamber by a rugged mechanical pump, so there is no high-pressure common rail to clog and no costly electronic injector to replace when fuel quality slips. The engine keeps its torque low in the rev range, sips diesel compared with electronically managed rivals, and starts reliably on sites where the fuel drum has been sitting in the sun for a month.
Hitachi has been building excavators since 1970 and the ZX series is the machine that taught the industry how to balance digging force against fuel burn. The wheeled version carries the same structural philosophy as the crawler: a box-section boom, a cast boom foot, and a reinforced upper frame that resists the torsional loads created when the machine works over the side. Independent tests of the ZX210W-6 consistently show competitive digging force with noticeably lower fuel consumption than the equivalent 20-ton crawler, which is why fleet buyers in Europe and Southeast Asia keep coming back to this model.
The real advantage for a buyer today is commercial rather than technical. A twenty-one ton Hitachi holds value because the second owner, and the third, can still find parts. Try that with an orphan brand and the machine becomes scrap the day a final drive fails. We supply the machine as inspected, with the hydraulic pressures checked, the tyres measured and a walk-around video recorded before loading.
Technical Specifications| Parameter | Specification |
|---|---|
| Model | Hitachi ZX210W-6 |
| Machine type | Wheeled hydraulic excavator |
| Operating weight | 21,400 kg (21.4 ton class) |
| Engine | Isuzu 4HK1X, turbocharged, direct injection |
| Rated power | 122 kW at 2,000 rpm |
| Bucket capacity | 0.9 m3 standard (0.8 - 1.2 m3 available) |
| Max digging depth | 5,700 mm |
| Max digging reach | 9,200 mm |
| Travel speed | 20 km/h working, up to 35 km/h transfer |
| Tyres | 10.00-20 16PR dual, twin circuit air brake |
| Fuel tank | 380 L |
| Overall width | 2,490 mm |
| Cab | ROPS / FOPS certified, air conditioned |
| Condition | Used, inspected, working ready |
Wheeled twenty-ton machines dominate municipal drainage, kerb and gutter replacement, water main renewal, street lighting cable trenches and small demolition inside city limits. The machine can drive itself to the next address after lunch, and the twin tyres spread load well enough to cross paved surfaces and compacted hardstanding without the repair bill a crawler leaves behind. On highway contracts it leapfrogs between culvert locations at thirty-five kilometres per hour, which is why road authorities in Europe and Southeast Asia keep wheeled units on permanent standby.
Built by a Factory, Not a Trading DeskWe are a manufacturer established in 2013, and we run a 3,000 square metre fabrication workshop with senior welders and modern cutting, forming and machining equipment. We manufacture excavator booms, sticks, buckets and amphibious excavator pontoons to order for every major brand, and we build custom attachments when a standard shell will not do the job. Alongside the fabrication line we trade used machines of all makes, so when you buy this ZX210W-6 you are dealing with people who repair, weld and rebuild the same structures you are about to put to work.
Practically, that means three things for you. Any bucket, quick coupler, thumb, ripper or long reach front end can be manufactured to match this machine before it ships. Wear parts can be bundled into the same container. And when the machine eventually needs structural repair, you already know where the workshop is.
Packaging, Loading and Quality AssuranceEach unit is pressure washed, drained where required, waxed on exposed chrome and secured with heavy-duty chains. We load in 40HQ containers on custom steel cradles, by flat rack, or ro-ro from Nansha and Shenzhen. Every machine is photographed at six angles before loading and the loading report is sent to you with the bill of lading. Price is negotiable and delivery runs two to five working days after confirmation for units in stock.
Questions Buyers Ask UsCan the machine be inspected before payment? Yes. You or your agent are welcome at our yard, and we will send a full video walk-around with the engine running, the hydraulics at working temperature and the hour meter visible.
Do you supply spare buckets? We manufacture them. Tell us the width and the application and we weld a shell to suit, in the same workshop that builds our amphibious pontoons.
What about shipping to my port? Send the port name and we will quote container, flat rack and ro-ro options with the total landed cost.
Talk to Sophie DirectlyEvery quotation on this machine is handled personally by our foreign trade manager. Send the model you need and you will receive the current condition report, a walk-around video and the exact shipping cost to your port within one working day.
Mobile / WhatsApp / WeChat: +86 18026254557
Email: hfsupply1@163.com
Website: www.excavators-spares.com
Workshop: 3,000 m2 fabrication base, Guangzhou, Guangdong, China
Send your inquiry directly to us